JNTUK R16 3-2 Geotechnical Engineering-1 Material PDF Download

Students those who are studying JNTUK R16 Civil Branch, Can Download Unit wise R16 3-2 Geotechnical Engineering-1 (GTE-1) Material/Notes PDFs below.

JNTUK R16 3-2 Geotechnical Engineering-1 Material PDF Download

OBJECTIVES:

• To enable the student to find out the index properties of the soil and classify it.
• To impart the concept of seepage of water through soils and determine the seepage discharge.
• To enable the students to differentiate between compaction and consolidation of soils and to determine the magnitude and the rate of consolidation settlement.
• To enable the student to understand the concept of shear strength of soils, assessment of the shear parameters of sands and clays and the areas of their application.

UNIT-1

Introduction: Soil formation – soil structure and clay mineralogy – Adsorbed water – Mass- volume relationship –Relative density , Mechanism of compaction – factors affecting – effects of compaction on soil properties – compaction control.

Download UNIT-1 Material PDF | Reference-2

UNIT-2

Index Properties Of Soils: Grain size analysis – Sieve and Hydrometer methods – consistency limits and indices – Various Types of soil Classifications – Unified soil classification and I.S. Soil classification.

Download UNIT-2 Material PDF | Reference-2

UNIT-3

Permeability: Soil water – capillary rise – One dimensioned flow of water through soils – Darcy’s law- permeability – Factors affecting –laboratory determination of coefficient of permeability –Permeability of layered systems. Total, neutral and effective stresses –quick sand condition – 2-D flow and Laplace’s equation – Seepage through soils – Flow nets: Characteristics and Uses.

Download UNIT-3 Material PDF | Reference-2

UNIT-4

Stress Distribution In Soils: Stresses induced by applied loads – Boussinesq’s and Westergaard’s theories for point loads and areas of different shapes– Newmark’s influence chart – 2:1 stress distribution method.

Download UNIT-4 Material PDF | Reference-2

UNIT-5

Consolidation: Compressibility of soils – e-p and e-log p curves – Stress history – Concept of consolidation – Spring Analogy – Terzaghi’s theory of onedimensional Consolidation – Time rate of consolidation and degree of consolidation – Determination of coefficient of consolidation (cv) – Over consolidated and normally consolidated clays.

Download UNIT-5 Material PDF | Reference-2

UNIT-6

Shear Strength of Soils: Basic mechanism of shear strength – Mohr – Coulomb Failure theories – Stress-Strain behavior of Sands – Critical Void Ratio – StressStrain behavior of clays – Shear Strength determination- various drainage conditions.

Download UNIT-6 Material PDF | Reference-2

TEXT BOOKS:

1. Basic and Applied Soil Mechanics, Gopal Ranjan and A. S. R. Rao, New Age International Publishers.
2. Soil Mechanics and Foundation Engineering, V. N. S. Murthy, CBS publishers

REFERENCE BOOKS:

1. Fundamentals of Soil Mechanics, D. W. Taylor, Wiley.
2. An introduction to Geotechnical Engineering, Holtz and Kovacs; Prentice Hall.
3. Fundamentals of Geotechnical Engineering, B M Das, Cengage Learning, New Delhi.

OUTCOMES:

• The student must know the definition of the various parameters related to soil mechanics and establish their inter-relationships.
• The student should be able to know the methods of determination of the various index properties of the soils and classify the soils.
• The student should be able to know the importance of the different engineering properties of the soil such as compaction, permeability, consolidation and shear strength and determine them in the laboratory.
• The student should be able to apply the above concepts in day-to-day civil engineering practice

JNTUK R16 3-2 Water Resource Engineering-1 Material PDF Download

Students those who are studying JNTUK R16 Civil Branch, Can Download Unit wise R16 3-2 Water Resource Engineering-1 (WRE-1) Material/Notes PDFs below.

JNTUK R16 3-2 Water Resource Engineering-1 Material PDF Download

OBJECTIVES:

• Introduce hydrologic cycle and its relevance to Civil engineering
• Make the students understand physical processes in hydrology and, components of the hydrologic cycle
• Appreciate concepts and theory of physical processes and interactions
• Learn measurement and estimation of the components hydrologic cycle.
• Provide an overview and understanding of Unit Hydrograph theory and its analysis
• Understand flood frequency analysis, design flood, flood routing
• Appreciate the concepts of groundwater movement and well hydraulics

UNIT-1

Introduction: Engineering hydrology and its applications, Hydrologic cycle, hydrological data-sources of data. Precipitation: Types and forms, measurement, raingauge network, presentation of rainfall data, average rainfall, continuity and consistency of rainfall data, frequency of rainfall, Intensity-Duration-Frequency (IDF) curves, Depth-Area-Duration (DAD) curves, Probable Maximum Precipitation (PMP), design storm

Download UNIT-1 Material PDF | Reference-2

UNIT-2

Abstractions from Precipitation: Initial abstractions. Evaporation: factors affecting, measurement, reduction Evapotranspiration: factors affecting, measurement, control Infiltration: factors affecting, Infiltration capacity curve, measurement, infiltration indices.

Download UNIT-2 Material PDF | Reference-2

UNIT-3

Runoff: Catchment characteristics, Factors affecting runoff, components, computation- empirical formulae, tables and curves, stream gauging, rating curve, flow mass curve and flow duration curve. Hydrograph analysis: Components of hydrograph, separation of base flow, effective rainfall hyetograph and direct runoff hydrograph, unit hydrograph, assumptions, derivation of unit hydrograph, unit hydrographs of different durations, principle of superposition and S-hydrograph methods, limitations and applications of unit hydrograph, synthetic unit hydrograph.

Download UNIT-3 Material PDF | Reference-2

UNIT-4

Floods: Causes and effects, frequency analysis- Gumbel’s and Log-Pearson type III distribution methods, Standard Project Flood (SPF) and Probable Maximum Flood (MPF), flood control methods and management. Flood Routing: Hydrologic routing, channel and reservoir routing-Muskingum and Puls methods of routing.

Download UNIT-4 Material PDF | Reference-2

UNIT-5

Ground water: Occurrence, types of aquifers, aquifer parameters, porosity, specific yield, permeability, transmissivity and storage coefficient, types of wells, Darcy’s law, Dupuit’s equation- steady radial flow to wells in confined and unconfined aquifers, yield of a open well-recuperation test.

Download UNIT-5 Material PDF | Reference-2

UNIT-6

Advanced Topics in Hydrology: Rainfall-runoff Modelling, instantaneous unit hydrograph (IUH) – conceptual models – Clark and Nash models, general hydrological models- Chow – Kulandaiswamy model

Download UNIT-6 Material PDF | Reference-2

TEXT BOOKS:

1. Engineering Hydrology, Jayarami Reddy, P., Laxmi Publications Pvt. Ltd., (2013), New Delhi
2. Irrigation and Water Power Engineering, B. C. Punmia, Pande B. B. Lal, Ashok Kumar Jain and Arun Kumar Jain, Lakshmi Publications (P) Ltd.

REFERENCE BOOKS:

1. Engineering Hydrology Subramanya, K, Tata McGraw-Hill Education Pvt Ltd, (2013),New Delhi.
2. Irrigation Engineering and Hydraulic Structure, Santosh Kumar Garg, Khanna Publishers.
3. Applied hydrology, Chow V. T., D. R Maidment and L.W. Mays, Tata McGraw Hill Education Pvt Ltd, (2011), New Delhi.
4. Water Resources Engineering, Mays L.W, Wiley India Pvt. Ltd, (2013).

OUTCOMES:

• have a thorough understanding of the theories and principles governing the hydrologic processes,
• be able to quantify major hydrologic components and apply key concepts to several practical areas of engineering hydrology and related design aspects
• develop Intensity-Duration-Frequency and Depth-Area Duration curves to design hydraulic structures.
• be able to develop design storms and carry out frequency analysis
• be able to determine storage capacity and life of reservoirs.
• develop unit hydrograph and synthetic hydrograph
• be able to estimate flood magnitude and carry out flood routing.
• be able to determine aquifer parameters and yield of wells.
• be able to model hydrologic processes

JNTUK R16 3-2 Environmental Engineering-1 Material/Notes PDF Download

Students those who are studying JNTUK R16 Civil Branch, Can Download Unit wise R16 3-2 Environmental Engineering-1 (EE-1) Material/Notes PDFs below.

JNTUK R16 3-2 Environmental Engineering-1 Material/Notes PDF Download

OBJECTIVES:

• Outline planning and the design of water supply systems for a community/town/city
• Provide knowledge of water quality requirement for domestic usage
• Impart understanding of importance of protection of water source quality and enlightens the efforts involved in converting raw water into clean potable water.
• Selection of valves and fixture in water distribution systems
• Impart knowledge on design of water distribution network

UNIT-1

Introduction: Importance and Necessity of Protected Water Supply systems, Water borne diseases, Flow chart of public water supply system, Role of Environmental Engineer, Agency activities Water Demand and Quantity Estimation: Estimation of water demand for a town or city, Per capita Demand and factors influencing it – Types of water demands and its variations- factors affecting water demand, Design Period, Factors affecting the Design period, Population Forecasting.

Download UNIT-1 Material PDF

UNIT-2

Sources of Water: Lakes, Rivers, Impounding Reservoirs, comparison of sources with reference to quality, quantity and other considerations- Capacity of storage reservoirs, Mass curve analysis. Groundwater sources of water: Types of water bearing formations, springs, Wells and Infiltration galleries, Yields from infiltration galleries. Collection and Conveyance of Water: Factors governing the selection of the intake structure, Types of Intakes. Conveyance of Water: Gravity and Pressure conduits, Types of Pipes, Pipe Materials, Pipe joints, Design aspects of pipe lines, laying of pipe lines

Download UNIT-2 Material PDF

UNIT-3

Quality and Analysis of Water: Characteristics of water–Physical, Chemical and Biological-Analysis of Water – Physical, Chemical and Biological characteristics. Comparison of sources with reference to quality- I.S. Drinking water quality standards and WHO guidelines for drinking water

Download UNIT-3 Material PDF

UNIT–4

Treatment of Water: Flowchart of water treatment plant, Treatment methods: Theory and Design of Sedimentation, Coagulation, Sedimentation with Coagulation, Filtration

Download UNIT-4 Material PDF

UNIT-5

Disinfection: Theory of disinfection-Chlorination and other Disinfection methods, Softening of Water, Removal of color and odours – Iron and manganese removal –Adsorption-fluoridation and deflouridation–aeration–Reverse Osmosis-Iron exchange– Ultra filtration

Download UNIT-5 Material PDF

UNIT–6

Distribution of Water: Requirements- Methods of Distribution system, Layouts of Distribution networks, Pressures in the distribution layouts, Analysis of Distribution networks: Hardy Cross and equivalent pipe methods -Components of Distribution system: valves such as sluice valves, air valves, scour valves and check valves, hydrants, and water meters–Laying and testing of pipe lines- selection of pipe materials, pipe joints

Download UNIT-6 Material PDF

TEXT BOOKS:

1. Environmental Engineering – Howard S. Peavy, Donald R. Rowe, Teorge George Tchobanoglus – Mc-Graw-Hill Book Company, New Delhi, 1985.
2. Elements of Environmental Engineering – K. N. Duggal, S. Chand & Company Ltd., New Delhi, 2012.

REFERENCE BOOKS:

1. 1.Water Supply Engineering – P. N. Modi.
2. Water Supply Engineering – B. C. Punmia
3. Water Supply and Sanitary Engineering – G. S. Birdie and J. S. Birdie
4. Environmental Engineering, D. Srinivasan, PHI Learning Private Limited, New Delhi, 2011.

OUTCOMES:

• Plan and design the water and distribution networks and sewerage systems
• Identify the water source and select proper intake structure
• Characterisation of water
• Select the appropriate appurtenances in the water supply
• Selection of suitable treatment flow for raw water treatments

JNTUK R16 3-2 Energy Audit, Conservation & Management Material PDF Download

Students those who are studying JNTUK R16 EEE Branch, Can Download Unit wise R16 3-2 Energy Audit, Conservation & Management Material/Notes PDFs below.

JNTUK R16 3-2 Energy Audit, Conservation & Management Material PDF Download

Preamble: This is an open elective course developed to cater the current needs of the industry. This course covers topics such as energy conservation act and energy conservation. It also covers energy efficient lighting design. The student will learn power factor improvement techniques, energy efficiency in HVAC systems. In addition The economic aspects such as payback period calculations, life cycle costing analysis is covered in this course.

OBJECTIVES:

• To understand energy efficiency, scope, conservation and technologies.
• To design energy efficient lighting systems.
• To estimate/calculate power factor of systems and propose suitable compensation techniques.
• To understand energy conservation in HVAC systems.
• To calculate life cycle costing analysis and return on investment on energy efficient technologies.

UNIT-1

Basic Principles of Energy Audit and management Energy audit – Definitions – Concept – Types of audit – Energy index – Cost index – Pie charts –Sankey diagrams – Load profiles – Energy conservation schemes and energy saving potential – Numerical problems – Principles of energy management – Initiating, planning, controlling, promoting, monitoring, reporting – Energy manager – Qualities and functions – Language – Questionnaire – Check list for top management.

Download UNIT-1 Material PDF

Unit–2

Lighting Modification of existing systems – Replacement of existing systems – Priorities: Definition of terms and units – Luminous efficiency – Polar curve – Calculation of illumination level – Illumination of inclined surface to beam – Luminance or brightness – Types of lamps – Types of lighting – Electric lighting fittings (luminaries) – Flood lighting – White light LED and conducting Polymers – Energy conservation measures.

Download UNIT-2 Material PDF

Unit–3

Power Factor and energy instruments Power factor – Methods of improvement – Location of capacitors – Power factor with non linear loads – Effect of harmonics on Power factor – Numerical problems. Energy Instruments – Watt–hour meter – Data loggers – Thermocouples – Pyrometers – Lux meters – Tong testers – Power analyzer.

Download UNIT-3 Material PDF

Unit–4

Space Heating and Ventilation Ventilation – Air–Conditioning (HVAC) and Water Heating: Introduction – Heating of buildings – Transfer of Heat–Space heating methods – Ventilation and air–conditioning – Insulation–Cooling load – Electric water heating systems – Energy conservation methods.

Download UNIT-4 Material PDF

Unit–5

Economic Aspects and Financial Analysis Understanding energy cost – Economics Analysis – Depreciation Methods – Time value of money – Rate of return – Present worth method – Replacement analysis – Life cycle costing analysis – Energy efficient motors (basic concepts) – Economics of energy efficient motors and systems.

Download UNIT-5 Material PDF

Unit–6

Computation of Economic Aspects Need of investment, appraisal and criteria – Calculation of simple payback period–Return on investment – Net present value – Internal rate of return – numerical examples – Power factor correction – Lighting – Applications of life cycle costing analysis – Return on investment – Numerical examples.

Download UNIT-6 Material PDF

TEXT BOOKS:

1. Hand Book of Energy Audit by Sonal Desai- Tata McGraw hill
2. Energy efficient electric motors by John .C. Andreas, Marcel Dekker Inc Ltd–2nd edition, 1995

REFERENCE BOOKS:

1. Energy management by W.R. Murphy & G. Mckay Butter worth, Elsevier publications. 2012
2. Electric Energy Utilization and Conservation by S C Tripathy, Tata McGraw hill publishing company Ltd. New Delhi.
3. Energy management by Paul o’ Callaghan, Mc–Graw Hill Book company–1st edition, 1998.
4. Energy management hand book by W.C.Turner, John wiley and sons.
5. Energy management and conservation –k v Sharma and pvenkataseshaiah-I K International Publishing House pvt.ltd,2011.

OUTCOMES:

• Explain energy efficiency, conservation and various technologies.
• Design energy efficient lighting systems.
• Calculate power factor of systems and propose suitable compensation techniques.
• Explain energy conservation in HVAC systems.
• Calculate life cycle costing analysis and return on investment on energy efficient technologies.

JNTUK R16 3-2 Unix and Shell Programming Material PDF Download

Students those who are studying JNTUK R16 EEE Branch, Can Download Unit wise R16 3-2 Unix and Shell Programming Material/Notes PDFs below.

JNTUK R16 3-2 Unix and Shell Programming Material PDF Download

OBJECTIVES:

• Written technical communication and effective use of concepts and terminology.
• Facility with UNIX command syntax and semantics.
• Ability to read and understand specifications, scripts and programs.
• Individual capability in problem solving using the tools presented within the class. Students will demonstrate a mastery of the course materials and concepts within in class discussions.

UNIT-1

UNIT-I Introduction to unix-Brief History-What is Unix-Unix Components-Using Unix-Commands in Unix-Some Basic Commands-Command Substitution-Giving Multiple Commands.

Download UNIT-1 Material PDF

UNIT-2

The File system –The Basics of Files-What’s in a File-Directories and File Names-Permissions-I Nodes-The Directory Hierarchy, File Attributes and Permissions-The File Command knowing the File Type-The Chmod Command Changing File Permissions-The Chown Command Changing the Owner of a File-The Chgrp Command Changing the Group of a File.

Download UNIT-2 Material PDF

UNIT-3

Using the Shell-Command Line Structure-Met characters-Creating New Commands-Command Arguments and Parameters-Program Output as Arguments-Shell Variables- -More on I/O Redirection-Looping in Shell Programs.

Download UNIT-3 Material PDF

UNIT-4

Filters-The Grep Family-Other Filters-The Stream Editor Sed-The AWK Pattern Scanning and processing Language-Good Files and Good Filters.

Download UNIT-4 Material PDF

UNIT-5

Shell Programming-Shell Variables-The Export Command-The Profile File a Script Run During Starting-The First Shell Script-The read Command-Positional parameters-The $? Variable knowing the exit Status-More about the Set Command-The Exit Command-Branching Control Structures-Loop Control Structures-The Continue and Break Statement-The Expr Command: Performing Integer Arithmetic-Real Arithmetic in Shell Programs-The here Document(<<)-The Sleep Command-Debugging Scripts-The Script Command-The Eval Command-The Exec Command.

Download UNIT-5 Material PDF

UNIT-6

The Process-The Meaning-Parent and Child Processes-Types of Processes-More about Foreground and Background processes-Internal and External Commands-Process Creation-The Trap Command-The Stty Command-The Kill Command-Job Control.

Download UNIT-6 Material PDF

TEXT BOOKS:

1. The Unix programming Environment by Brain W. Kernighan & Rob Pike, Pearson.

2. Introduction to Unix Shell Programming by M.G.Venkateshmurthy, Pearson.

REFERENCE BOOKS:

1. Unix and shell programmingby B.M. Harwani, OXFORD university press.

OUTCOMES:

• Documentation will demonstrate good organization and readability.
• File processing projects will require data organization, problem solving and research.
• Scripts and programs will demonstrate simple effective user interfaces.
• Scripts and programs will demonstrate effective use of structured programming.
• Scripts and programs will be accompanied by printed output demonstrating completion of a test plan.
• Testing will demonstrate both black and glass box testing strategies.
• Project work will involve group participation.

JNTUK R16 3-2 DATA STRUCTURES THROUGH C++ Material PDF Download

Students those who are studying JNTUK R16 EEE Branch, Can Download Unit wise R16 3-2 DATA STRUCTURES THROUGH C++ Material/Notes PDFs below.

JNTUK R16 3-2 DATA STRUCTURES THROUGH C++ Material PDF Download

OBJECTIVES:

• To be familiar with basic techniques of object oriented principles and exception handling using C++
• To be familiar with the concepts like Inheritance, Polymorphism
• Solve problems using data structures such as linear lists, stacks, queues, hash tables
• Be familiar with advanced data structures such as balanced search trees, AVLTrees, and B Trees.

UNIT-1

ARRAYS

Abstract Data Types and the C++ Class, An Introduction to C++ Class- Data Abstraction and Encapsulation in C++- Declaring Class Objects and Invoking Member Functions- Special Class Operations- Miscellaneous Topics- ADTs and C++Classes, The Array as an Abstract Data Type, The Polynomial Abstract Data type- Polynomial Representation- Polynomial Addition. Spares Matrices,Introduction- Sparse Matrix Representation- Transposing a Matrix- Matrix Multiplication, Representation of Arrays.

Download UNIT-1 Material PDF

UNIT-2

STACKS AND QUEUES

Templates in C++, Template Functions- Using Templates to Represent Container Classes, The Stack Abstract Data Type, The Queue Abstract Data Type, Subtyping and Inheritance in C++, Evaluation of Expressions, Expression- Postfix Notation- Infix to Postfix.

Download UNIT-2 Material PDF

UNIT-3

LINKED LISTS

Single Linked List and Chains, Representing Chains in C++, Defining a Node in C++- Designing a Chain Class in C++- Pointer manipulation in C++- Chain Manipulation Operations, The Template Class Chain, Implementing Chains with Templates- Chain Iterators- Chain Operations- Reusing a Class, Circular Lists, Available Space Lists, Linked Stacks and Queues, Polynomials, Polynomial Representation- Adding Polynomials- Circular List Representation of Polynomials, Equivalence Classes, Sparse Matrices, Sparse Matrix Representation- Sparse Matrix Input- Deleting a Sparse Matrix, Doubly Linked Lists, Generalized Lists, Representation of Generalized Lists- Recursive Algorithms for ListsReference Counts, Shared and Recursive Lists

Download UNIT-3 Material PDF

UNIT-4

TREES

Introduction, Terminology, Representation of Trees, Binary Trees, The Abstract Data Type, Properties of Binary Tress, Binary Tree Representations, Binary Tree Traversal and Tree Iterators, Introduction, Inorder Traversal Preorder Traversal, Postorder Traversal, Thread Binary Trees, Threads, Inorder Traversal of a Threaded Binary Tree, Inserting a Node into a Threaded Binary Tree, Heaps, Priority Queues, Definition of a Max Heap, Insertion into a Max Heap, Deletion from a Max Heap, Binary Search Trees, Definition, Searching a Binary Search Tree, Insertion into a Binary Search Tree, Deletion from a Binary Search Tree, Height of Binary Search Tree.

Download UNIT-4 Material PDF

UNIT-5

GRAPHS

The Graph Abstract Data Type, Introduction, Definition, Graph Representation, Elementary Graph Operation, Depth First Search, Breadth First Search, Connected Components, Spanning Trees, Biconnected Components, Minimum Cost Spanning Trees, Kruskal S Algorithm, Prim s Algorithm Sollin’ s Algorithm, Shortest Paths and Transitive Closure, Single Source/All Destination: Nonnegative Edge Cost, Single Source/All Destination: General Weights, All-Pairs Shortest Path, Transitive Closure.

Download UNIT-5 Material PDF

UNIT-6

SORTING

Insertion Sort, Quick Sort, Merge Sort Merging, Iterative Merge Sort, Recursive Merge Sort, Heap Sort.

Download UNIT-6 Material PDF

TEXT BOOKS:

1. Data structures, Algorithms and Applications in C++, S.Sahni, University Press (India) Pvt.Ltd, 2nd edition, Universities Press, Pvt. Ltd.
2. Data structures and Algorithm Analysis in C++, Mark Allen Weiss, Pearson Education. Ltd.Second, Edition.
3. Data structures and Algorithms in C++, Michael T.Goodrich, R.Tamassia and Mount, Wiley student edition, John Wiley and Sons.

REFERENCE BOOKS:

1. 1.Data structures and algorithms in C++, 3rd Edition, Adam Drozdek, Thomson
2. Data structures using C and C++, Langsam, Augenstein and Tanenbaum, PHI.
3. Problem solving with C++, The OOP, Fourth edition, W.Savitch, Pearson education.

OUTCOMES:

• Distinguish between procedures and object oriented programming.
• Apply advanced data structure strategies for exploring complex data structures.
• Compare and contrast various data structures and design techniques in the area of Performance.
• Implement data structure algorithms through C++.
• Incorporate data structures into the applications such as binary search trees, AVL and B Trees
• Implement all data structures like stacks, queues, trees, lists and graphs and compare their Performance and trade offs